Modification of the trapped field in bulk high-temperature superconductors as a result of the drilling of a pattern of artificial columnar holes
Gregory P. Lousberg, J. -F. Fagnard, M. Ausloos, Ph. Vanderbemden, B. Vanderheyden
arXiv:1005.2834 · DOI 10.1088/1742-6596/234/1/012023 · 2010-05-17
Active bibliographic source — not scientific approval
Bibliographic access preserves source history; it does not approve extracted materials or validate reported claims. Review warnings on each occurrence separately.
Abstract
The trapped magnetic field is examined in bulk high-temperature superconductors that are artificially drilled along their c-axis. The influence of the hole pattern on the magnetization is studied and compared by means of numerical models and Hall probe mapping techniques. To this aim, we consider two bulk YBCO samples with a rectangular cross-section that are drilled each by six holes arranged either on a rectangular lattice (sample I) or on a centered rectangular lattice (sample II). For the numerical analysis, three different models are considered for calculating the trapped flux: (i), a two-dimensional (2D) Bean model neglecting demagnetizing effects and flux creep, (ii), a 2D finite-element model neglecting demagnetizing effects but incorporating magnetic relaxation in the form of an E-J power law, and, (iii), a 3D finite element analysis that takes into account both the finite height of the sample and flux creep effects. For the experimental analysis, the trapped magnetic flux density is measured above the sample surface by Hall probe mapping performed before and after the drilling process. The maximum trapped flux density in the drilled samples is found to be smaller than that in the plain samples. The smallest magnetization drop is found for sample II, with the centered rectangular lattice. This result is confirmed by the numerical models. In each sample, the relative drops that are calculated independently with the three different models are in good agreement. As observed experimentally, the magnetization drop calculated in the sample II is the smallest one and its relative value is comparable to the measured one. By contrast, the measured magnetization drop in sample (1) is much larger than that predicted by the simulations, most likely because of a change of the microstructure during the drilling process.
Source-reported materials — not catalogue approval
| Formula | Reported Tc (K) | Pressure (GPa) | Type |
|---|---|---|---|
| YBa2Cu3O7-δ Archive — visibility unverified Source-occurrence policy only; no material identity or catalogue acceptance is inferred from the formula. | — | Pressure not reported | unknown |
Similar papers
Pulsed-field magnetization of drilled bulk high-temperature superconductors: flux front propagation in the volume and on the surface
similarity 0.88Gregory P Lousberg et al. · 2009 · arXiv:0908.1907
Source status unknown — claims are unverified
Bulk high-Tc superconductors with drilled holes: how to arrange the holes to maximize the trapped magnetic flux ?
similarity 0.87Gregory P Lousberg et al. · 2008 · arXiv:0811.1834
Source status unknown — claims are unverified
Measurement of the magnetic field inside the holes of a drilled bulk high-Tc superconductor
similarity 0.87Gregory P Lousberg et al. · 2008 · arXiv:0811.1894
Source status unknown — claims are unverified
Modelling nonlocal electrodynamics in superconducting films: The case of a concave corner
similarity 0.87J. I Vestgarden & T. H. Johansen · 2012 · arXiv:1205.0338
Source status unknown — claims are unverified
Numerical simulation of the magnetization of high-temperature superconductors: 3D finite element method using a single time-step iteration
similarity 0.87Gregory P. Lousberg et al. · 2008 · arXiv:0811.2883
Source status unknown — claims are unverified
Numerical evaluation of AC losses in an HTS insert coil for high field magnet during its energization
similarity 0.86K. Kajikawa et al. · 2014 · arXiv:1405.7765
Source status unknown — claims are unverified