Beneficial influence of Hf and Zr additions to Nb4at.%Ta on the vortex pinning of Nb$_{3}$Sn with and without an O source
Shreyas Balachandran, Chiara Tarantini, Peter J. Lee, Fumitake Kametani, Yi-Feng Su, Benjamin Walker, William L. Starch, David C. Larbalestier
arXiv:1811.08867 · DOI 10.1088/1361-6668/aaff02 · 2018-11-21 · Superconductor Science and Technology
Active bibliographic source — not scientific approval
Bibliographic access preserves source history; it does not approve extracted materials or validate reported claims. Review warnings on each occurrence separately.
Abstract
Here we show that addition of Hf to Nb4Ta can significantly improve the high field performance of Nb$_{3}$Sn, making it suitable for dipole magnets for Future Circular Collider (FCC). A big challenge for the FCC is that a realistic production target for FCC Nb3Sn requires ~30% improvement over current conductor performance. Recent success with internal oxidation(IO) of Nb-Zr precursor has shown significant improvement in the layer J$_{c}$ of Nb$_{3}$Sn wires, albeit the complication of providing an internal O$_{2}$ diffusion path and avoiding degradation of irreversibility field($_{irr}$). We compare Zr and Hf additions to the standard Nb4Ta alloy of maximum H$_{c2}$ and H$_{irr}$. Nb4Ta rods with 1Zr or 1Hf were made into monofilament wires with and without SnO$_{2}$ and their properties measured over the entire superconducting range up to 31 T. We found that group IV alloying of Nb4Ta raises H$_{irr}$, though adding O$_{2}$ still degrades this slightly. As noted in Nb1Zr studies, the pinning force density F$_{p}$ is strongly enhanced and its peak value shifted to higher field by IO. A surprising result of this work is that we found better properties in Nb4Ta1Hf without SnO$_{2}$, F$_{pmax}$ achieving 2.35 times that of the standard Nb4Ta alloy, while the oxidized Nb4Ta1Zr alloy achieved 1.54 times that of the Nb4Ta alloy. The highest layer J$_{c}$ (16 T, 4.2 K) of 3700 A/mm$^{2}$ was found in the SnO$_{2}$-free wire made with Nb4Ta1Hf alloy. Using a standard A15 cross-section fraction of 60% for modern PIT and RRP wires, we estimated that a non-Cu J$_{c}$ of 2200 A/mm$^{2}$ is obtainable in modern conductors, well above the 1500A/mm$^{2}$ FCC specification. Moreover, the best properties were obtained without SnO$_{2}$, the Nb4Ta1Hf alloy appears to open a straightforward route to enhanced properties in Nb$_{3}$Sn wires.
Source-reported materials — not catalogue approval
| Formula | Reported Tc (K) | Pressure (GPa) | Type |
|---|---|---|---|
| Nb3Sn Archive — visibility unverified Source-occurrence policy only; no material identity or catalogue acceptance is inferred from the formula. | — | Pressure not reported | unknown |
Similar papers
Ta, Ti and Hf effects on NbSn high-field performance: temperature-dependent dopant occupancy and failure of Kramer extrapolation
similarity 0.88Chiara Tarantini et al. · 2019 · arXiv:1908.07548
Source status unknown — claims are unverified
Evidence from EXAFS for Different Ta/Ti Site Occupancy in High Critical Current Density NbSn Superconductor Wires
similarity 0.87Steve M. Heald et al. · 2018 · arXiv:1803.07025
Source status unknown — claims are unverified
Performance Boost in Industrial Multifilamentary Nb3Sn Wires due to Radiation Induced Pinning Centers
similarity 0.87T. Baumgartner et al. · 2015 · arXiv:1504.05366
Source status unknown — claims are unverified
Ultra-low magnetization and hysteresis loss in APC Nb3Sn superconductors
similarity 0.87X Xu et al. · 2026 · arXiv:2601.09945
Source status unknown — claims are unverified
Achievement of FCC specification in critical current density for Nb3Sn superconductors with artificial pinning centers
similarity 0.87X Xu et al. · 2019 · arXiv:1903.08121
Source status unknown — claims are unverified
High Critical Temperature and Field Superconductivity in NbX, (X = Ti, Zr, Hf) Alloys: Promising Candidates for Superconducting Devices
similarity 0.86R. K. Kushwaha et al. · 2025 · arXiv:2512.18821
Source status unknown — claims are unverified